 |
American
Mobile Research, Inc. |
| 1955
CBS Court |
(307)
235-4590 |
Office |
| Casper,
WY 82604 |
(307) 265-4489 |
Fax |
2011 LABORATORY FEE SCHEDULE |
 |
|
(Routine
Hydrocarbon Analysis of Gases and Pressurized Liquids)
(Extended
Gas and Liquid Hydrocarbon Studies)
(Sulfur
Fractional Analysis of Gas and Liquid Hydrocarbons)
(Aromatic
(BETX) Analysis of Gas and Liquid Hydrocarbons)
(Chromatographic
Quick List Services Reference Quick List)
|
|
I. ROUTINE HYDROCARBON ANALYSIS OF GASES AND PRESSURIZED LIQUIDS
A.) HYDROCARBON FRACTIONAL
ANALYSIS OF GASES
The gas fractional analysis includes the
separation and the quantification of Nitrogen, Carbon Dioxide, and Methane
to through Hexanes (C6+) plus hydrocarbons. The calculations provided
with each sample include the Specific Gravity, BTU’s (dry & wet basis),
Ideal Gross Heating Value, Gallons per Thousand (GPM), Average Molecular
Weight, Molar Mass Ratio, Compressibility Factor, and Relative Density.
All analyses are performed in accordance to
GPA 2261 methodology.
| Cost of Analysis, C1 to C6+, N2, CO2, per sample |
|
$65.00 |
| Cost of Analysis, C1 to C6+, N2, CO2, over 10 samples submitted |
$60.00 |
Additional Gas Analysis |
|
| Inert Gas Analysis, (Argon, Nitrogen, Oxygen, Carbon Monoxide), per Sample |
$145.00 |
| Oxygen Content of Natural Gas by TCD Analysis, per Sample |
$135.00 |
| Organic / Inorganic Chlorides in Natural Gas, per Sample |
$165.00 |
|
Tutweiler Analysis for the determination of
Hydrogen Sulfide in Gases, corrected to STP |
$95.00 |
| Methanol, Glycol, Amines, and other
contaminants in Gas, per sample |
$165.00 |
Trace Metals Analysis by ICP-AES of Natural Gas, per Sample**
**Test for Arsenic and Mercury in Natural Gas requires Gas Scrub. Contact Lab for details. |
QUOTE |
Note: For additional gas testing, such as Extended
Hydrocarbons (C10+), Extended Sulfur Studies, and Aromatic (BETX)
Analysis, please see
accompanying sections.
B.) PRESSURIZED LIQUID HYDROCARBON FRACTIONAL ANALYSES
This analysis, which is applicable to
Liquefied Ethane, Propane, Butanes, NGL’s, Condensates and Drip Liquids,
includes the separation and quantification of Nitrogen, Carbon Dioxide,
and Methane through Heptane (C7+) plus hydrocarbons. Calculations provided
with this analysis include Mole Percent, Weight Percent, and Liquid Volume
Percentage Distributions. Also inclusive is the Specific Gravity, Average
Molecular Weight, and True Vapor Pressure (calculated), Lbs/Gallon, and
Cubic Feet gas/Gallon of Liquid.
All analyses are performed in accordance to
GPA-2177 Methodology. All sampling of Pressurized Liquids that are
submitted for analysis must conform to the methods outlined in
GPA-2174-96, using Piston Cylinders, or Water Displacement. If you have any questions
regarding the sampling of Pressurized Liquids, please contact our laboratory at (307)
235-4590.
| Cost of Analysis, C1 to
C7+ Routine Liquid Study of NGL, Propane and Butane Products |
$120.00 |
| Cost of Analysis, C1 to
C7+ Routine Liquid Study of Gasolines, Condensates and Heavier |
$135.00 |
Additional Liquid Analyses
| Reid Vapor Pressure, ASTM D-323, per sample |
$65.00 |
| Copper Strip Corrosion, ASTM D-130, per sample |
$55.00 |
| Saybolt Color, ASTM D-156, per
sample |
$35.00 |
| API Gravity of Petroleum Products, ASTM D-287, per
sample |
$10.00 |
|
Residue Number, ASTM 2158, per
sample |
$75.00 |
|
Oil Stain Observation Number, ASTM 2158, per
sample |
$50.00 |
| Organic / Inorganic Chlorides in Hydrocarbon Liquid, per sample |
$180.00 |
|
Contaminant Identification, (Glycols, Amines, Compressor
Oils), per sample |
$165.00 |
Note: For additional Liquid testing, such as
Extended Hydrocarbon (C10+ or C20+), Extended Sulfur Studies, Aromatic (BETX)
Studies, please see
accompanying sections.
Return to top of page
|
|
II. EXTENDED
HYDROCARBON ANALYSIS OF GASES AND PRESSURIZED LIQUIDS
A.)
EXTENDED HYDROCARBON FRACTIONAL ANALYSIS OF GASES.
The gas fractional analysis includes the separation and
quantification of Nitrogen, Carbon Dioxide, and Methane to Decane (C10+)
plus Hydrocarbons. If requested, the analysis can be detailed out to the
Eicosane (C20+) plus range. The calculations provided with each analysis
include the Specific Gravity, BTU's (dry & wet basis), Ideal Gross
Heating Value, Gallons per Thousand (GPM), Average Molecular Weight, Molar
Mass Ratio, Relative Density, and Compressibility Factor (Z).
All analysis are performed in accordance to
GPA
2286 Methodology.
| Extended Hydrocarbon Gas Analysis (C1to C10+, N2, CO2), per sample |
$165.00 |
| Extended Hydrocarbon Gas Analysis (C1to C20+, N2, CO2), per sample |
$195.00 |
| Extended Glycalc Hydrocarbon Gas Analysis (C1to C8+,detailed BETX), per sample |
$180.00 |
B.)
EXTENDED HYDROCARBON FRACTIONAL ANALYSIS OF PRESSURIZED LIQUIDS.
This Extended analysis, which is applicable to NGLs,
Condensates, Drips, and Oil samples, includes the separation and
quantification of Nitrogen, Carbon Dioxide, and Methane to Decane (C10+)
plus, or, Eicosane (C20+) plus Hydrocarbons. Calculations provided with
this analysis include Mole Percent, Weight Percent, and Liquid Volume
Percentage distributions. Additional calculations include the Specific
Gravity, Average Molecular Weight, Average Boiling Point (F), True Vapor
Pressure, and the Density of the C10+ fraction. Aromatics (BETX) analyses
may be added for an additional fee. Please see accompanying section (IV)
for price details regarding Aromatics in Pressurized Liquid Hydrocarbons.
All analysis are performed in accordance to
GPA
2186 Methodology. All samples should be taken by
GPA
2174, for Pressurized Liquids, or, contact our laboratory for
additional sampling instructions of Atmospheric Liquids.
| Extended Hydrocarbon Fractional Liquid Analysis, (C1
to C10+, N2, CO2), per sample |
$175.00 |
| Extended Hydrocarbon Fractional Analysis, (C1
to C20+, N2, CO2), per sample |
$205.00 |
| Extended Hydrocarbon Glycalc Fractional Analysis, (C10
to C10+, detailed BTEX), per sample |
$195.00 |
| Extended Hydrocarbon Analysis of Crude Oils,( C1
to C20+, N2, CO2, BETX), per sample |
$215.00 |
|
|
Additional Crude Oil Testing |
|
| Reid Vapor Pressure, ASTM D-323, per sample |
$65.00 |
| Pour Point of Crude Oil, ASTM D 5853, per sample |
$65.00 |
| Asphaltene Content (Heptane Insoluble), ASTM D6560, per sample |
$90.00 |
| Water Content of Crude Oil, ASTM D4928, per sample |
$50.00 |
| Total Sulfur Content of Crude Oil, ASTM D-5453, per sample |
$95.00 |
C.)
CONTAMINANT STUDIES ON HYDROCARBON GASES AND LIQUIDS
This analysis is available for the identification and
quantification of Impurities, such as Glycols, Amines, Alcohols, Ketones,
and a wide range of Oils (Lean Oil, Compressor Oil, Lube Oils). We can
also determine many of the Treating Chemicals used in Gas and Liquid
Plants, Pipelines, and Wells. This test may also be applicable to Solids,
such as Molecular Sieve, Alumina Beds, Zinc Oxide Beds, and many other
pellet treaters.
| Cost of Contaminant Study
on Hydrocarbon Gases, per sample |
$165.00 |
| Cost of Contaminant Study
on Hydrocarbon Liquids, per sample |
$195.00 |
| Cost of Contaminant Study
on Glycols, Amines, Lubricating Oils, per sample |
$155.00 |
| Cost of Impurity Analysis on Petrochemicals (Alcohols, Ketones, etc.), per sample |
$125.00 |
| Cost of Contaminant Study
on Solids, per sample |
$195.00 |
Return
to top of page
|
|
III. SULFUR FRACTIONAL ANALYSIS OF GAS AND LIQUID
HYDROCARBONS
|
Note:
Due to the reactive nature of Sulfurous Compounds, in both gas and
liquid hydrocarbons, it is preferable to obtain these samples in either,
Treated Stainless or Teflon Lined sampling cylinders, to prevent the
possible passivation of Sulfur Compounds, such as Hydrogen Sulfide, into
the metal walls. Recent studies by our Lab indicate Sulfur Compounds like
H2S and Mercaptans can be absorbed through passivation, which begins
almost immediately in Stainless Steel and most untreated metals. Within 1
hour of sampling, 95% of the Hydrogen Sulfide was passivated into the
metal walls of the cylinders. Treated Stainless (Sulfinert) and Teflon
lined cylinders held 99% of all sulfurs, for two weeks or more without
passivation. Although Mercaptans and Disulfides are usually slow to
passivate in cylinders, our study shows that 95% of these Sulfurs will
passivate within 24 Hours, in standard metal cylinders.
Our
Laboratory maintains a large stock of Sulfinert and Teflon Lined sampling
cylinders, both sale and use, for our customers. If you are attempting to
sample gases or liquids for Treater designs, or analytical testing, please
contact our Laboratory prior to sampling. We will be glad to assist you
with sampling procedures, or Teflon lined cylinders and cases, to assure
quality results. |
A.)
SULFUR FRACTIONAL ANALYSIS OF GASEOUS OR LIQUID
HYDROCARBONS
Utilizing a
Sievers Model 355 Sulfur Chemiluminescence Chromatograph, our laboratory
can speciate and quantitate all Sulfur Compounds, down to a 10 part per
billion level quickly and accurately. Listed are Carbonyl Sulfide,
Hydrogen Sulfide, Carbon Disulfide, Dimethyl Sulfide, Dimethyl Disulfide,
Sulfur Dioxide, and a complete distribution of Mercaptans and Thiophenes.
This instrument allows a complete analysis of all Sulfur Compounds in
both, Gases and Liquids, in about 30 minutes.
The basic
theory of operation is based on the chemiluminescence (light producing
reaction) from the reaction of Ozone with Sulfur Monoxide (SO) produced
from combustion of the analyte tested. A vacuum pump pulls the combustion
products into a reaction cell at low pressure, where excess Ozone is
added. Light produced from the subsequent reaction is detected with a
blue-sensitive photomultiplier tube.
| The Extended Sulfur Fractional Analyses listed below for Gas and Liquid samples includes analysis of the following Sulfur Compounds: |
|
| |
|
| Hydrogen Sulfide, Methyl Mercaptain, Thiophenes, Carbonyl Sulfide, Ethyl Mercaptan, Methyl Mercaptan, Carbon Disulfide, Propyl Mercaptans, Benzothiophene, Dinethyl Sulfide, Butyl Mercaptans, Methylbenzothiopenes, Dimethyl Disulfide, Pentyl & Heavier, Dimethylbenzothiopenes |
|
| |
|
| Extended Sulfur Fractional
Analysis of Gases, ASTM D-5504, per sample |
$175.00 |
| Extended Sulfur Fractional
Analysis of Liquids, ASTM D-5623, per sample |
$195.00 |
| Extended Sulfur Fractional
Analysisof Crude Oils, ASTM D-5623, per sample |
$210.00 |
| |
|
| |
|
| Total Sulfur Content of Hydrocarbon Liquids, (Gasoline Range) ASTM D-5453, per sample |
$110.00 |
| Total Sulfur Content of Low Sulfur Gasoline or Diesel, ASTM D-5453, per sample |
$125.00 |
| Total Sulfur Content of Water, ASTM D-5453, per sample |
$95.00 |
| Total Sulfur Content of Crude and Lube Oils, ASTM D-5453, per sample |
$120.00 |
| Elemental Sulfur Content of Hydrocarbon Liquids, UOP-165-59, per sample |
$135.00 |
|
|
IV.
AROMATIC (BETX) ANALYSIS OF GAS AND LIQUID HYDROCARBONS.
A.) AROMATIC ANALYSIS OF GASES.
The analysis of Aromatic
constituents in Natural Gas and Air Vapors includes the determination and
quantification of Benzene, Ethylbenzene, Toluene, and Xylenes. Both, high
pressure gases and atmospheric tank vapors can be analyzed, using Flame
Ionization Chromatography, for the required Aromatic compounds. Additional Aromatics, such as
Chlorobenzene and Dichlorobenzene can be requested at the time of
analysis.
| Cost
of Aromatic (BETX) Analysis on Gases or Air, per
sample |
$165.00 |
B.) AROMATIC ANALYSIS OF PRESSURIZED LIQUIDS AND CONDENSATES.
Both, high pressure and
atmospherically flashed tank liquids can be analyzed for the Aromatic
constituents, using Flame Ionization Chromatography. The analysis includes
the determination and quantification of Benzene, Ethylbenzene, Toluene,
and Xylenes, in Butanes, NGLs, Condensates, Gasolines, and Oil samples.
| Cost
of Aromatic (BETX) Analysis on Liquids, per
sample |
$195.00 |
Return
to top of page
|
|
V. ANALYTICAL
SERVICES REFERENCE QUICK LIST
  
| GAS
AND LIQUID HYDROCARBON STUDIES |
TURNAROUND
TIME ** |
COST/SAMPLE |
|
|
|
| ROUTINE GAS ANALYSIS, C1
TO C6+, N2, CO2 |
24 HRS |
$65.00 |
| INERT GAS STUDIES, H2, O2, N2, CO, CO2, AR |
24 HRS |
$145.00 |
| EXTENDED GAS ANALYSIS, C1
TO C10+, N2, CO2, BETX COMPONENTS |
24 HRS |
$165.00 |
| EXTENDED GAS GLYCALC ANALYSIS, C1
TO C8+, DETAILED BTEX |
24 HRS |
$180.00 |
| EXTENDED GAS ANALYSIS, C1
TO C20+, N2, CO2 |
24 HRS |
$195.00 |
| ORGANIC/INORGANIC CHLORIDES IN NATURAL GAS |
24 HRS |
$165.00 |
| |
|
|
| ROUTINE LIQUID ANALYSIS,
C1 TO C7+, N2, CO2 FOR NGL, PROPANE, BUTANES |
24 HRS |
$120.00 |
| ROUTINE LIQUID ANALYSIS,
C1 TO C7+, N2, CO2 FOR GASOLINE AND HEAVIER |
24 HRS |
$135.00 |
| EXTENDED LIQUID ANALYSIS,
C1 TO C10+, N2, CO2, BETX COMPONENTS |
48 HRS |
$175.00 |
| EXTENDED LIQUID GLYCALC ANALYSIS,
C1 TO C10+, DETAILED BTEX |
48 HRS |
$195.00 |
| EXTENDED CRUDE OIL ANALYSIS,
C1 TO C10+, DETAILED BTEX |
48 HRS |
$215.00 |
| EXTENDED LIQUID ANALYSIS,
C1 TO C20+, N2, CO2 |
48 HRS |
$205.00 |
| ORGANIC/INORGANIC CHLORIDES IN HYDROCARBON LIQUIDS |
48 HRS |
$180.00 |
| |
|
|
| EXTENDED SULFUR ANALYSIS
OF GASES, ASTM D-5504 |
24 HRS |
$175.00 |
| EXTENDED SULFUR ANALYSIS
OF HYDROCARBON LIQUIDS, ASTM D-5623 |
24 HRS |
$195.00 |
| EXTENDED SULFUR ANALYSIS
OF CRUDE OILS, ASTM D-5623 |
24 HRS |
$210.00 |
| TOTAL SULFUR CONTENT OF LOW SULFUR DIESEL OR GASOLINE, ASTM D-5453 |
|
|
| TOTAL SULFUR CONTENT OF CRUDE OIL, ASTM D-5453 |
|
|
| TOTAL SULFUR CONTENT OF LIGHT HYDROCARBONS, ASTM D-5453 |
24 HRS |
$125.00 |
| ELEMENTAL SULFUR CONTENT OF HYDROCARBON LIQUID, UOP-165-59 |
24 HRS |
$120.00 |
| |
|
|
| ONSITE SAMPLING AND TECHNICIAN FEES |
|
|
| |
|
|
| TECHNICIAN TIME, SAMPLING
SERVICES, PER DAY |
ONSITE |
$850.00 |
| TECHNICIAN TIME,
TRUCK FACILITIES, PER HOUR |
ONSITE |
$47.50 |
| TECHNICIAN TIME, PICKUP
AND DELIVERY, PER DAY |
ONSITE |
$500.00 |
| SULFINERT SAMPLING
CYLINDER RENTAL, PER WEEK |
|
$7.50 |
| CYLINDER SHIPPING CASE RENTAL,
PER WEEK |
|
$10.00 |
| |
|
|
| DESULFURIZATION AND METAL ABSORBANT TREATER STUDIES |
|
|
| |
|
|
| TREATER ABSORBANT
STUDY ON GASES, PER DAY |
|
QUOTED |
| TREATER ABSORBANT
STUDY ON LIQUIDS, PER DAY |
|
QUOTED |
| |
|
|
| METAL ABSORBANT
STUDY ON LIQUIDS, PER DAY |
|
QUOTED |
| SYNGAS TREATER
ABSORBANT STUDIES, PER DAY |
|
QUOTED |
ADDITIONAL TEST PROCEDURES FOR HYDROCARBONS, WATER, SOILS |
| PURGEABLE AROMATICS
(BETX) ON WATER (EPA 602) |
EPA-602 |
$155.00 |
| TOTAL PETROLEUM
HYDROCARBONS ON WATER (EPA 8015M) |
EPA-8015 |
$125.00 |
| TOTAL PETROLEUM
HYDROCARBONS ON SOILS (EPA 8015M) |
EPA-8015 |
$140.00 |
| TOTAL OIL AND GREASE CONTENT ON SOIL OR WATER |
EPA-1664 |
$90.00 |
| TOTAL ORGANICS (TOX)
STUDY ON WATERS (EPA 601) |
SW-9020 |
$165.00 |
| KARL FISCHER COULOMETRIC WATER CONTENT, PER SAMPLE |
E1064-00 |
$90.00 |
| VISCOSITY OF OILS (KINEMATIC), PER SAMPLE |
D-445 |
$85.00 |
| CLOUD POINT OF HYDROCARBON LIQUIDS, PER SAMPLE |
D-2500 |
$60.00 |
| POUR POINT OF HYDROCARBON LIQUIDS, PER SAMPLE |
D-97 |
$75.00 |
| ENGLER DISTILLATION OF HYDROCARBON LIQUIDS, PER SAMPLE |
D-86 |
$160.00 |
| ROUTINE CATIONS/ANIONS IN WATER, PER SAMPLE |
E300.00 |
$195.00 |
| VOLATILE SULFUR COMPOUNDS IN WATER, PER SAMPLE |
D-5453 |
$195.00 |
| VOLATILE SULFUR COMPOUNDS IN AIR, PER SAMPLE |
D-5504 |
$175.00 |
| HYDROGEN SULFIDE BY TUTWEILER PROCEDURE, PER SAMPLE |
UOP 9-85 |
$95.00 |
| API or SPECIFIC GRAVITY ON LIQUIDS, PER SAMPLE |
D-287 |
$10.00 |
| TOTAL ALKALINITY as CaCO3, ON WATERS, PER SAMPLE |
E310.1 |
$25.00 |
| CHLORIDE CONTENT OF WATER, PER SAMPLE |
E300.0 |
$35.00 |
| ORGANIC/INORGANIC CHLORIDES ON HYDROCARBON LIQUIDS, PER SAMPLE |
D-4929B |
$180.00 |
|
ICP - INORGANIC METALS STUDIES
IN HYDROCARBON LIQUIDS AND LUBRICATING FLUIDS |
| 20 TRACE METALS IN GAS TURBINE FUELS, PER SAMPLE |
D-3605 |
$150.00 |
| 22 ADDITIVE ELEMENTS IN LUBE OILS, PER SAMPLE |
D-4951 |
$165.00 |
| 16 WEAR
METALS IN LUBE OILS, PER SAMPLE |
D-5185 |
$115.00 |
| ADDITIONAL METALS BY ICP-AES ON OILS,
PER ELEMENT |
D-4951 |
$25.00 |
| DIGESTION PROCEDURE FOR OILS AND SLUDGES, PER SAMPLE |
|
$125.00 |
|
ICP -AES - TOXIC CHARACTERISTIC METALS ON LIQUIDS AND SOLIDS |
| TCLP METALS DIGESTION FOR SOLIDS or SOILS, PER SAMPLE |
SW 3050 |
$95.00 |
| TCLP METALS DIGESTION FOR LIQUIDS, PER SAMPLE |
SW 3010 |
$85.00 |
| TCLP ZERO HEADSPACE EXTRACTION FOR VOLATILES, PER SAMPLE |
SW 1311 |
$150.00 |
| |
|
|
| TCLP EXTRACTABLE METALS ON LIQUIDS, PER SAMPLE |
ICP-AES |
$145.00 |
| TCLP EXTRACTABLE METALS ON
SOILS or SOLIDS, PER SAMPLE |
ICP-AES |
$165.00 |
| ADDITIONAL ICP METALS BY ICP-AES, PER ELEMENT |
ICP-AES |
$25.00 |
**Estimated Turnaround
Time. Times may be different, depending on volume in laboratory.
For Volume Discounts or Bid Proposals,
please contact our office.
NOTE: IN
ADDITION TO OUR MANY CHROMATOGRAPHIC SERVICES, OUR LABORATORY IS WELL
EQUIPPED TO HANDLE MANY TESTS NOT LISTED IN THIS FILE. PLEASE FEEL FREE
TO CONTACT
OUR LABORATORY TO INQUIRE ABOUT
TESTING AND PRICES THAT YOU MAY REQUIRE.
WE ALSO
MAINTAIN SAMPLING CYLINDERS, PPE BOTTLES AND VARIOUS SUPPLIES THAT YOU
MAY REQUIRE TO PERFORM YOUR OWN SAMPLING. LET US KNOW WHAT YOUR
REQUIREMENTS ARE AND WE WILL BE GLAD TO ASSIST YOU.
Return
to top of page
If your Hydrocarbon product requires further treatment and removal of Sulfur compounds you might be interested in this product. Click on the link to learn more.
|
|
 |
